background image

Powered by Safety

®

2

General Information

01.4IB.51051C

PowlVac

®

 Remote Racking Device Assembly 

for PowlVac® CDR 5kV & 15kV Circuit Breakers

A.  S

cope

The information in this instruction bulletin 

describes the following PowlVac

®

 Remote 

Racking Device and components for use 

with PowlVac CDR 5kV & 15kV vacuum circuit 

breakers:

•  51897G11 - Remote Racking Device and    

Motor Control Box (complete assembly)

•  51899G10 - Remote Racking Device

•  51895G01 - Motor Control Box

B.  p

urpoSe

The information in this instruction bulletin is 

intended to provide information required to 

properly operate and maintain the  

PowlVac Remote Racking Device and 

components

 

described in 

Ch 1 General 

Information, A. Scope

.

This instruction bulletin provides:

1.  Safety guidelines

2.  General descriptions of the operation 

and maintenance of the PowlVac Remote 

Racking Device and components

3.  Instructions for installation

4.  Illustrations, photographs, and description 

of the equipment described in  

Ch 1 General Information, A. Scope

The illustrations and photos in this document 

are provided as general information to aid in 

showing component locations only.  

All illustrations and photos are shown using 

deenergized equipment.

Follow the appropriate safety precautions 

while handling any of the equipment.  Failure 

to do so may result in death or serious injury.

!

WARNING

To the extent required, the products described 

herein meet the applicable ANSI, IEEE, and 

NEMA Standards; however, no such assurance 

is given with respect to local codes and 

ordinances which may vary greatly.

c.  I

nStructIon

 B

ulletInS

 A

vAIlABle

 e

lectronIcAlly

Changes to the instruction bulletin may be 

implemented at any time and without notice.  

Go t

powellind.com

 to ensure use of the current 

instruction bulletin for Powell equipment.

NOTICE

To contact the Powell Service Division call 

1.800.480.7273 or 713.944.6900, or email  

[email protected]

.

For specific questions or comments pertaining 

to this instruction bulletin email  

[email protected]

 with the Instruction 

Bulletin number in the subject line.

Summary of Contents for PowlVac 01.4IB.51051C



























Reviews: