background image

13

MAINTENANCE

 

Engine oil

 

Pivot points

➂ 

Interlock 

bosses

LUBRICATION CHART

GENERAL REC OM MEN DA TIONS

The warranty on this snow thrower does not cover items 

that have been sub ject ed to operator abuse or negligence.  

To receive full value from the warranty, operator must 

maintain snow thrower as in struct ed in this manual.  Some 

ad just ments will need to be made periodically to properly 

maintain your snow thrower.
All adjustments in the Service and Ad just ments section of 

this manual should be checked at least once each season.
•  Once a year, you should replace the spark plug and 

check belts for wear.  A new spark plug will help your 

engine run better and last longer.

•  Follow the maintenance schedule in this manual.

NOTE:

 Use only Original Equipment Manufacturer (OEM) 

parts to service this unit.  Failure to do so can cause the 

unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.  Check engine oil level.
2.  Check for loose fasteners.
3.  Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated

(See “LU BRI CA TION CHART”).
At the beginning of each season, or every 25 hours of 

use, apply a small amount of white lithium grease to the 

interlock bosses.

 

SAE 5w30 Motor Oil

 

See “Engine” in Maintenance section

 

White Lithium Grease

Summary of Contents for PR240













































Reviews: