background image

37

REPAIR PARTS

TRACTOR - MODEL NUMBER PDGT26H48C

STEERING ASSEMBLY

1         180656           Wheel, Steering
 2        178557           Axle Asm., Front 
 3        183226           Fitting, Grease
 4        161849           Spindle Asm, LH
 5        161848           Spindle Asm., RH
 6        6266H            Bearing, Race Thrust Harden
 7        121748X        Washer  25/32 x 1-5/8 x 16 Ga.
 8        12000029       Ring, Klip #T5304-75
 9        121232X        Cap, Spindle
10       74781044       Bolt, Fin Hex  5/8-11 x 2-3/4
11       136518           Spacer, Brg. Axle Front
12       73901000       Nut, Lock Flange  5/8-11 unc
13       121749X        Washer  25/32 x 1-1/4 x 16 Ga.
14       10040600       Washer, Lock Hvy Hlcl Spr  3/8
15       73540600       Nut Crownlock 3/8-24 
16       186814           Shaft Asm., Steering
18       175572           Draglink, Ball Joint Solid Vgt
19       156011           Support Asm., Steering Vgt
20       163887X428  Boot Steering Stealth
21       159945           Adapter, Wheel Steering
22       155105           Bushing, Strg. 
23       152927           Screw
25       74780616       Bolt, Fin Hex  3/8-16 x 1 Gr. 5
26       180657           Insert Cap Strg WH
27       3366R            Bearing, Col. Strg.
28       17000612       Screw Hexwsh thdr 3/8-16 x 3/4
29       104239X        Bearing, Flange 
31       138136           Bushing, Nyliner Snap 
32       19111610       Washer  11/32 x 1 x 10 Ga.
33       10040500       Washer, Lock Hvy Hlcl Spr  5/16
34       74780512       Bolt, Hex Hd  5/16-18 x 3/4
35       187039           Gear, Sector Steering
36       186799           Tie Rod
41       155246           Bracket Switch Interlock Vgt 97
42       17490508       Screw Thdrol  5/16-18 x 1/2 Tyt
45       19182411       Washer 9/16 x 1-1/2 x 11 Ga.
46       19131610       Washer 13/32 x 1 x 10 Ga.
47       179471           Bracket Asm. Idler Stationary
48       17060612       Screw 3/8-16 x .75
49       175820           Pulley Idler Flat
50       73900600       Nut Lock Flg. 3/8-16 unc
52       175553           Clip Steering
53       188967           Washer Hardened

KEY    PART
NO.     NO.                DESCRIPTION

NOTE:

 

 

All component dimensions given in U.S. inches

             1 inch = 25.4 mm

Summary of Contents for PDGT26H48C

















































Reviews: