Poulan Pro 187301 Page 10 Owner'S Manual Download

Page: 10 / 44

OPERATION

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments.
Save this manual for future reference.

Our tractors conform to the safety standards of the American National Standards Institute.

ATTACHMENT CLUTCH LEVER

- Used to engage the

mower blades, or other attachments mounted to your
tractor.

LIGHT SWITCH POSITION

- Turns the headlights on and

off.

THROTTLE/CHOKE CONTROL

- Used for starting and

controling engine speed.

CLUTCH/BRAKE PEDAL

- Used for declutching and brak-

ing the tractor and starting the engine.

PARKING BRAKE

- Locks clutch/brake pedal into the

brake position.

LIFT LEVER
PLUNGER

ATTACHMENT
LIFT LEVER

PARKING
BRAKE

IGNITION
SWITCH

THROTTLE/CHOKE
CONTROL

LIGHT SWITCH
POSITION

MOTION
CONTROL
LEVER

CLUTCH/BRAKE
PEDAL

FIG. 4

FREE WHEEL
CONTROL

AT TACH MENT
CLUTCH LEVER

FREEWHEEL CONTROL

- Disengages transmission for

pushing or slowly towing the tractor with the engine off.

MOTION CONTROL LEVER

- Selects the speed and

di rec tion of tractor.

ATTACHMENT LIFT LEVER

- Used to raise and lower

the mower deck or other attachments mounted to your
tractor.

LIFT LEVER PLUNGER

- Used to release attachment lift

lever when changing its position.

IGNITION SWITCH

- Used for starting and stopping the

engine.

Summary of Contents for 187301













































Search results

Summary of Contents for 187301

Reviews:

Related manuals for 187301

Brands by name

Popular brands

Poulan Pro 187301, Owner'S Manual

Search results

Summary of Contents for 187301

Reviews:

Related manuals for 187301

Brands by name

Popular brands