Poulan Pro 115156426 Instruction Manual Download

Page: 15 / 21

CHECK GUIDE BAR

Conditions which require guide bar mainte-

nance:

Saw cuts to one side or at an angle.

Saw has to be forced through the cut.

Inadequate supply of oil to bar/chain.

Check the condition of guide bar each time

chain is sharpened. A worn guide bar will

damage the chain and make cutting difficult.

After each use, ensure ON/STOP switch is

in the STOP position, then clean all sawdust

from the guide bar and sprocket hole.

To maintain guide bar:

Move ON/STOP switch to STOP.

Loosen and remove bar nuts and clutch

cover. Remove bar and chain from saw.

Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

Burring of guide bar rails is a normal

process of rail wear. Remove these burrs

with a flat file.

When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct Groove

Worn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when ex-

cess heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHECK FUEL MIXTURE LEVEL

See FUELING ENGINE under the OP-

ERATION section.

LUBRICATION

Bar Oil

Fill Cap

See GUIDE BAR AND CHAIN OIL under

the OPERATION section.

INSPECT AND CLEAN UNIT AND

DECALS

After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

Wipe off unit with a clean dry cloth.

CHECK CHAIN BRAKE

See CHAIN BRAKE in the OPERATION

section.

CLEAN AIR FILTER

CAUTION:

Do not clean filter in gasoline or

other flammable solvent to avoid creating a

fire hazard or producing harmful evaporative

emissions.

Cleaning the air filter:

A dirty air filter decreases the life and perfor-

mance of the engine and increases fuel con-

sumption and harmful emissions. Always

clean your air filter after 10 tanks of fuel or 5

hours of operation, whichever comes first.

Clean more frequently in dusty conditions. A

used air filter can never be completely

cleaned. It is advisable to replace your air fil-

ter with a new one after every 50 hours of op-

eration, or annually, whichever comes first.

1. Loosen 3 screws on cylinder cover.

2. Remove cylinder cover.

3. Remove air filter cover and air filter.

4. Clean the air filter using hot soapy water.

Rinse with clean cool water. Air dry com-

pletely before reinstalling.

5. Reinstall air filter and air filter cover.

6. Reinstall cylinder cover and 3 screws.

Tighten securely.

Air Filter

Cover

Cylinder

Cover

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

occur.

Nut

Exhaust

Outlet

Cover

Muffler

Spark

Arresting

Screen

Summary of Contents for 115156426






















Search results

Summary of Contents for 115156426

Reviews:

Related manuals for 115156426

Brands by name

Popular brands

Poulan Pro 115156426, Instruction Manual

Search results

Summary of Contents for 115156426

Reviews:

Related manuals for 115156426

Brands by name

Popular brands