manualshive.com logo in svg

Poulan Pro 115156426, Instruction Manual

Share
Download
Poulan Pro 115156426 Instruction Manual Download Page 7

7

Adjustment located on clutch cover

Inside

view of

clutch

cover

4. Turn the adjusting screw by hand coun-

terclockwise until the adjusting pin just

touches the stop. This should allow the

pin to be near the correct position.

5. Slide guide bar on bar bolts until guide

bar stops against clutch drum sprocket.

Guide bar

Bar bolts

6. Carefully remove the chain from the pack-

age. Hold chain with the drive links as

shown.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Tip of

Bar

Cutters

Depth Gauge

Drive Links

7. Place chain over and behind clutch re-

tainer, fitting the drive links in the clutch

drum sprocket.

8. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

9. Fit chain drive links into bar groove.

10. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive

links are in the bar groove.

11. Now, install clutch cover making sure

the adjusting pin is positioned in the low-

er hole in the guide bar. Remember this

pin moves the bar forward and back-

ward as the screw is turned.

Clutch

Cover

Lower

Hole

Guide Bar

Adjusting Pin

12. Install bar nuts and finger tighten only.

Once the chain is tensioned, you will

need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING:

Wear protective gloves

when handling chain. The chain is sharp and

can cut you even when it is not moving.

NOTE:

When adjusting chain tension,

make sure the chain brake nuts are finger

tight only. Attempting to tension the chain

when the chain brake nuts are tight can

cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move chain around

guide bar. If the chain does not rotate, it is too

tight. If the chain is too loose, it will sag below

the bar.

Bar Nuts

Chain Adjustment

Tool

(Bar Tool)

Guide

Bar

Adjusting

Screw

Adjusting the tension:

Chain tension is very important. Chains

stretch during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time be-

fore you start the chain saw.

1. Loosen bar nuts until they are finger tight

against the clutch cover.

2. Turn adjusting screw clockwise until chain

solidly contacts bottom of guide bar rail.

Adjusting

Screw

Summary of Contents for 115156426






















Reviews:

No comments

Brands by name

Popular brands

Load more brands