Potterton WH 46 Installation, Operation And Maintenance Manual Download | Manualshive

Page: 18 / 36

background image

18

INSTRUCTIONS PERTAINING TO THE INSTALLER

926.772.1 - GB/IE

(Pumped heating circuits with Room Thermostat and compensated circuit with remote control QAA73, inclu-
ding hot-water tank, with primary loop)

13.2 HYDRAULIC SYSTEM 2

•  TS:Tank Sensor (QAZ36)*
•  B3: Room Control Module (QAA73)*
•  B1: Room Thermostat
•  B9: Temperature Sensor (QAC34)*
•  Zone Controller (Clip-in AGU2.500)*
•  FS: Flow Sensor (QAD36: supplied with AGU2.500)*
•  P1: Heating Pump
•  P DHW: Hot Water pump
•  PLP: Primary Pump
•  3WV: 3-way Valve (power open / power close)

(*) Available Optional Extra

•  Pumps (Not Supplied)
•  Isolating Valve (Not Supplied)
•  Installer Wiring --------------
•  Hot Water Cylinder (Not Supplied)
•  Low Loss Header (Not Supplied)
•  Non Return Valve (Not supplied)

Figure 10

0602_0705/CG1759

AGU 2.500

*

HEATING CIRCUIT
COSTANT TEMP.

HEATING CIRCUIT
VARIABLE TEMP.

*

*

*

*

«
...
16
17
18
19
20
...
»

Summary of Contents for WH 46





































Reviews:

No comments

Related manuals for WH 46

Luna Duo-Tec MP 1.35

Brand: Baxi Pages: 92

Henrad WH 100 FF

Brand: IDEAL Pages: 4

Vitodens 200-W B2HA-45

Brand: Viessmann Pages: 184

Combi Compact ECO RF 24

Brand: Intergas Pages: 4

BRITONY System II 80

Brand: C&M Pages: 12

Combi 25 Eco Elite

Brand: Main Pages: 56

Brand: Beem Pages: 88

Britony SE 100 L.P.G.

Brand: Chaffoteaux & Maury Pages: 16

Brand: Chaffoteaux & Maury Pages: 20

Brand: Vaillant Pages: 64

Bryan DR Series

Brand: Bryan Boilers Pages: 2

Bryan Knockdown CLM-120 29

Brand: Bryan Boilers Pages: 4

A-H-FS-15-12-50-D operati

Brand: Bryan Boilers Pages: 17

Brand: Harman Stove Company Pages: 40

Brand: Worcester Pages: 4

Greenstar utility 32-50kW

Brand: Worcester Pages: 44

Brand: Rinnai Pages: 28

Brand: Rinnai Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands