background image

2

926.772.1 - GB/IE

INSTRUCTIONS PERTAINING TO THE USER

Dear Customer,

We are sure your new boiler will comply with all your requirements.

Do not dispose of this booklet as it contains the information, which will help you to run your 
boiler correctly and efficiently.

POTTERTON GOLD HIGH OUTPUT

 boilers bear the CE mark in compliance with the 

basic requirements as laid down in the following Directives:

- Gas Directive 2009/142/CE

- Performance Directive 92/42/CEE

- Electromagnetic Compatibility Directive 2004/108/CE

- Low Voltage Directive 2006/95/CE

Do not leave any parts of the packaging (plastic bags, polystyrene, etc.) within children’s reach as they are a 
potential source of danger.

1. Instructions prior to installation 

3

2. Instructions prior to commissioning 

3

3. Commissioning of the boiler 

4

4. Filling the boiler 

10

5. Turning off the boiler 

10

6. Prolonged standstill of the system. Frost protection  

10

7. Servicing instructions 

10

8. General information 

11

9. Instructions prior to installation 

11

10. Boiler installation 

12

11. Boiler size 

13

12. Installation of flue and air ducts 

13

13. Hydraulic system 

16

14. Connecting the mains supply 

20

15. Gas valve adjustment 

27

16. Setting the boiler parameters 

29

17. Control and operation devices 

30

18. Positioning of the ignition and flame sensing electrode 

31

19. Check of combustion parameters 

31

20. Activating the chimney-sweep function 

32

21. Annual service 

32

22. Boiler schematic 

33

23. Illustrated wiring diagram 

34

24. Technical data 

35

CONTENTS

INSTRUCTIONS PERTAINING TO THE USER

INSTRUCTIONS PERTAINING TO THE INSTALLER

Summary of Contents for WH 46





































Reviews: