Potterton Mersey Super Installation And Service Instructions Manual Download Page 29

Page: 29 / 35

Fig. 35

Page 17

7. FAULT FINDING - Page 18

SYMPTON

POSSIBLE CAUSE

SOLUTION

PILOT WILL NOT LIGHT

1. Gas not turned on.

1. Turn on the gas at the

service cock and/or the main

gas line.

2. Air in gas line.

2. Purge the air line by

depressing and holding the

centre ON button, this may

take 2-3 minutes.

3. Incorrect pilot lighting procedure. 3. Follow the lighting

instructions located on the

bottom cover or refer to the

"Instructions for Use".

4. Electrode lead not connected to

the rear of the spark igniter.

4. Re-connect the electrode

lead.

5. Incorrect spark gap.

5. The gap between the

electrode tip and the pilot

hood should be 3-4mm.

6. Current tracking to earth.

6. Check the electrode lead

is routed clear of all metal

parts.

7. Pilot injector blocked.

7. Clear injector by blowing

through or replace with pilot

injector Part No 19/12690

Also clean the lint filter

Page 29 of 35

Mersey Super - Installation & Service Instructions

09/12/2009

file://P:\System\DATA\Dx\DS1\installation\2551\I24-2551\I24-2551.htm

Summary of Contents for Mersey Super




































Search results

Summary of Contents for Mersey Super

Reviews:

Related manuals for Mersey Super

Brands by name

Popular brands

Potterton Mersey Super, Installation And Service Instructions Manual

Search results

Summary of Contents for Mersey Super

Reviews:

Related manuals for Mersey Super

Brands by name

Popular brands