Potterton EC Plus 120 Installation Manual Download Page 28

Page: 28 / 52

EXPLANATIONS ON THE EXAMPLES

Parameter Name

Factory setting

New setting

Remarks

Example 3

552

HydrSys

553

KonfigHks

Both circuits controlled by RRG

(see table 10 for details)

CTC controlled by HKM/EMS
VTC controlled by RRG

506, 507

TvSMin, TvSMax

20/70

Set according to user

’

s needs

(see table 7 for details)

Example 4

552

HydrSys

553

KonfigHks

Both circuits controlled by RRG

(see table 10 for details)

CTC controlled by HKM/EMS
VTC controlled by RRG

618

KonfigEingangR

Set to heat exchanger/door veil

619

KonfigAusgang1R

Set to heat exchanger/door veil

Example 5a/5b

552

HydrSys

with CIM

with ZR EC 1/2 and CIB

553

KonfigHks

VTC controlled by RRG

615

KonfigAusgang

5b (primary loop pump) only

558.0

KonfigRg4

0 (OFF)

1 (ON)

5b (primary loop pump) only

Example 6a/6b/6c

552

HydrSys

553

KonfigHks

Both circuits controlled by RRG

CTC controlled by HKM/EMS
VTC controlled by RRG

615

KonfigAusgang

6b, c (primary loop pump) only

558.0

KonfigRg4

0 (OFF)

1 (ON)

6b, c (primary loop pump) only

Example 7

552

HydrSys

555.2

KonfigRg1

1 (ON)

0 (OFF)

Set room thermostat function

618

KonfigEingangR

Set input to

“

flow sensor

“

619

KonfigAusgang1R

Set output to

“

secondary loop pump

“

–

Connect pump M1 to exit M1

–

Connect pump M6 (max. 0.5 A) and sensor B6 to CITF

Example 9a/9b

552

HydrSys

615

KonfigAusgang

9b (primary loop pump) only

558.0

KonfigRg4

0 (OFF)

1 (ON)

9b (primary loop pump) only

–

Connect primary loop pump to M5

Example 11, 14

552

HydrSys

For all boilers in the system!

605

LPBAdrGerNr

condensing boiler in the cascade

–

Any other parameter settings, see manuals of BCA 2 und EUROCONTROL KK for details.

General:
If external control such as ZR EC 1/2, EC MSR or EC M are used, always set the hydraulic system (param. 552) to 66.

Note:

Take out CISP if another relay clip-in used, e.g. CIR, CIST, CITF.

Summary of Contents for EC Plus 120





















































Search results

Summary of Contents for EC Plus 120

Reviews:

Related manuals for EC Plus 120

Brands by name

Popular brands

Potterton EC Plus 120, Installation Manual

Search results

Summary of Contents for EC Plus 120

Reviews:

Related manuals for EC Plus 120

Brands by name

Popular brands