background image

 

 

Part 1 

 
 
 
 
 

 

FCC Notes: 

This  equipment  generates,  uses,  and  can  radiate  radio 
frequency  energy  and,  if  not  installed  and  used  in 
accordance  with  the  instructions  manual,  may  cause 
interference to radio communications. It has been tested 
and  found  to  comply  with  limits  for  a  Class  A  digital 
device  pursuant  to  subpart  J  of  Part  15  of  FCC  Rules, 
which  are  designed  to  provide  reasonable  protection 
against  interference  when  operated  in  a  commercial 
environment.  Operation  of  this  equipment  in  a  residential  area  is  likely  to  cause  interference  in 
which case the user at his own expense will be required to take whatever measures to correct the 
interference. 

Warranty Limits: 

Warranty  terminates  automatically  when  any  person  other  than  the  authorized  technicians  opens 
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if 
the user does not follow the instructions in application of this merchandise. The manufacturer is by 
no means responsible for any damage or hazard caused by improper application. 

About This Manual: 

Posiflex has made every  effort for the accuracy of the content in this manual. However, Posiflex 
will  assume  no  liability  for  any

 

technical  inaccuracies  or  editorial  or  other  errors  or  omissions 

contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including 
without limitation loss of data or profits, resulting from the furnishing, performance, or use of this 
material.

 

This  information  is  provided  “as  is”  and  Posiflex  Technology,  Inc.  expressly  disclaims  any 
warranties,  expressed,  implied  or  statutory,  including  without  limitation  implied  warranties  of 
merchantability or fitness for particular purpose, good title and against infringement. 
The information in this manual contains only essential hardware concerns for general user and is 
subject  to  change  without  notice.  Posiflex  Technology,  Inc.  reserves  the  right  to  alter  product 
designs,  layouts  or  drivers  without  notification.  The  system  integrator  shall  provide  applicative 
notices and arrangement for special options utilizing this product. The user may find the most up 
to  date  information  of  the  hardware  from  web  sites: 

http://www.posiflex.com

  or 

http://www.posiflex.com.tw

 

All  data  should  be  backed-up  prior  to  the  installation  of  any  drive  unit  or  storage  peripheral. 
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this 
or any other Posiflex product. 
All  rights  are  strictly  reserved.  No  part  of  this  documentation  may  be  reproduced,  stored  in  a 
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, 
or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of 
this documentation. 

©

 Copyright Posiflex Technology, Inc. 2011

 

All brand and product names and trademarks are the property of their respective holders.

 

PD-300  SERIES 

2 X 20 LCD 

CUSTOMER DISPLAY

 

Rev. D0 

 

P/N: 19430900070 

 

PD302 

PD303 

PD305 

PD306/U  PD307/U  PD308/U 

Summary of Contents for PD-300 Series











Reviews: