manualshive.com logo in svg

POSIFLEX PD - 2600, User Manual, Page: 8 / 11

Share
Download
POSIFLEX PD - 2600 User Manual Download Page 8

 

 

Part 8 

Fixing pole display base to system 

To fix the PD-2602 to base of KS or TP systems, please connect the interface 

cable of PD-2602 through the cable exit in base as 
in 

Pix.  9

    a  peeping  view 

of  pole  display  joint  base 
bottom  to  the  appropriate 
port  in  main  unit  passing 
the  inside  of  system  base 

as indicated in the top-view picture 

Pix. 10

. Match the 

pole base (joint mechanism) to the system rear connect 
area Fit 2 screws 

through  washers

 at arrowed points 

to hold the joint tight. 
 

INSTALLING PD-2603 

Open back cover on system 

First push in the circled knobs on 
both  sides  as  in 

Pix.  11

  to 

remove the back cover. 
 

Remove pole cover 

Remove  the  pole  cover  on  rear  edge  of  the  base  top 
cover  of  FT  system  by  first  removing  the  2  arrowed 
screws in 

Pix. 12

 and then pushing the wedge shaped 

pole cover up. 
 

Install PD and connect interface cable 

Insert  the  base  of  PD-2603  /  PD-2603U  from  top  of 
FT  system  base  with  the  flat  side  of  the  pole  base 
facing the back cover direction and screw back the 2 
screws  as  in 

Pix.  13

.  Connect  the  interface  cable  to 

appropriate port. 
 

 

COMMAND EMULATION MODE SETUP 

 
 
 
 
 
 
 

Pix. 9 

Pix. 10 

DIP switch 
window 

Pix. 14 

Pix. 12 

Pix. 11 

Pix. 13 

Summary of Contents for PD - 2600












Reviews:

No comments