background image

 

 

Part 2 

II.

 

CARTON CONTENTS 

1.

 

Touch Monitor (Main unit + Adjustable base stand assembly) 

2.

 

User’s Manual 

3.

 

VGA cable 

4.

 

USB cable 

5.

 

Power adaptor & power cord(For TM/LM-8115) 
(For  TM-8315,  please  refer  to  the  terminals  manual  to  support  power 
from VGA cable) 

6.

 

Posiflex Product Information CDROM 

7.

 

Option RS232 cable 

 

III.

 

INSTALLATION GUIDE  

TM/LM-8115 

Since the monitor and stand are packaged separately, 
please take out and hold the PE foams carefully and 

DO NOT detach and drop it

 as show in the 

following picture. 

 

 
After  take  the  PE  foam  out  from  the 
carton, please remove the PE foam with 
extra  care  and  make  sure  place  the 
monitor  and  stand  on  a  soft  clean  flat 
surface such as table and as show in the 
picture at the right side.  
 
 
Please  find  the  four  holes  in  the  top  of  stand. 
Take  the  stand  and  align  these  four  matching 
holes to the four matching pegs which are in the 
back on monitor. 
 
 
 
After matching the stand and monitor, push the 
stand to the arrowed direction as show in the right 
picture. At this time, turn the monitor to the normal 
position and plug the power then it can start to use. 

Summary of Contents for LM-8115
















Reviews: