background image

 

 

Part 1 

 

 
 
 

I.

 

FEATURES 

 

LM/TM-8115 is a stand along LCD monitor for industrial and commercial use. 

 

TM-8315  is  a  second  display  which  suit  for  Posiflex  POS  Terminals  with  Gen.5 
base stand. 

 

Application covers POS, Factory Automation etc. 

 

High quality 15” TFT LCD panel with scaling function for full screen display. 

 

TM-8315  support  power  supply  through  LCD  cable  from  Posiflex  Terminals 
(Power  supply  need  to  setup  from  terminal  and  please  refer  to  the  terminal’s 
manual). 

 

Recommended LCD resolution: 1024 x 768 

 

Resistive  type  extra  long  life  touch  panel  in  USB  interface  or  RS232  interface 
(option) supports touch panel function including left/right button, double click, drag 
& drop 

 

Touch  beep  can  be  pitch  adjusted/enabled/disabled  by  software  control  (for  TM-
8115/TM-8315) 

 

USB HUB function with 2 ports for optional side mount devices (SD-400Z or KP-
300) 

 

Connect to host through VGA port plus USB port (for all models) and/or COM port 
(for RS232 touch model only) 

 

Support 2 downlink USB ports 

FCC NOTICE

 

This  equipment  generates,  uses,  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the 
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class 
A  digital  device  pursuant  to  subpart  J  of  Part  15  of  FCC  Rules,  which  are  designed  to  provide  reasonable  protection  against 
interference  when  operated  in  a  commercial  environment.  Operation  of  this  equipment  in  a  residential  area  is  likely  to  cause 
interference in which case the user at his own expense will be required to take whatever measures to correct the interference. 

WARRANTY LIMITS 

Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user 
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of 
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application. 

ABOUT THIS MANUAL

 

This  manual assists the user to utilize the  LCD  Monitor LM-8115 series  and the Touch Monitor TM-8115/TM-8315 series. This 
product provides exquisite touch control capability over a stable and adjustable LCD monitor with minimal footprint. 

The  manufacturer of the LM-8115 / TM-8115 / TM-8315 touch  monitor heartily  apologizes to the user  for reserving the right to 
change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology. 
The  user  may  always  obtain  the  most  up  to  date  information  through  any  of  our  web  sites:  http://www.posiflex.com, 
http://www.posiflex.com.tw, http://www.posiflexusa.com.

 

 Copyright Posiflex Technology, Inc. 2011 

TRADE MARKS AND SERVICE MARKS 

POSIFLEX is a registered trademark of Posiflex Technology, Inc. 

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners. 

P/N: 

19690903030

 

LM-8115 / TM-8115 / TM-8315

 

LCD Touch Monitor

 

User’s Manual

 

Rev. B0 

Summary of Contents for LM-8115
















Reviews: