background image

 

 

Part 10 

full screen display of Windows DOS box should be avoided. 

E.

 

APPLICATION LIMITATION 

The USB touch is not applicable for OS other than Windows as USB mouse is 
not  supported  in  DOS  environment.  The  USB  touch  is  also  not  applicable 
when  the  monitor  is  used  to  be  the  extended  screen  in  multiple  monitor 
application. 
 
In using the MSR of the side mounted upgrade option for reading a magnetic 
stripe card, be sure to insert the card to the bottom with magnetic stripe facing 
the  mark aside the slot. The movement of the card can be either inserting the 
card from the top surface then sliding the card down out of the slot, or sliding 
the  card  upward  from  the  lower  side  of  the  slot  till  it  reaches  the  top  end  as 
long  as  the  card  is  a  standard  one.  A  non-standard  card  recorded  without 
complete  degaussing  prior  to  recovery  may  accept  only  one  direction  in  card 
reading. 
 
If the fingerprint sensor option is installed in the side mount kit, please find the 
most comfortable angle for the fingerprint taking operation in consideration of 
the LCD panel tilt angle and try to align the core of fingerprint in the sensing 
area. 
 

IX.

 

LED MODULE INDICATION 

 

Green: standby 

 

Blue: power on 

When  this  touch  monitor  is  turned  ON,  the  LED  light  is  in  blue.  When  the 
VGA signal vanishes, the monitor shows “No signal” for a while and goes into 
standby mode and LED is green. However, the touch panel is still operational. 

 

X.

 

OSD

 

(ON SCREEN DISPLAY) SCREEN ADJUST FUNCTION

 

A.

 

OSD buttons 

The  4  OSD  control buttons  are  above  the  power 

switch button on left side of the LCD panel. 

“OSD” button

: To enter OSD setup menu, or to 

perform function selected in OSD operation. 

“NXT” button

: To go to next option function. 

” 

   

” button

: To increase setting value. 

    

” button

: To decrease setting value. 

Summary of Contents for LM-8115
















Reviews: