background image

 

 

Part 15

connected there but found inoperable by such messages. 

Emergency treatment: 

The battery is constructed maintenance free and leakproof. It is well 

protected in  FT system as long as the ambient temperature remains below 
30

°

C and the ventilation of the FT system remains free. However, should any 

accident happen and the sulfuric acid from the battery spills on skin or clothing, 
wash immediately with water. If the acid comes in contact with eyes, rinse 
eyes with large amount of clean water and see a doctor immediately. A larger 
external battery may be connected to give an extended operation. Please check 
your dealer about this capability when required. 

WARNING: 

If there are any signs of over charging or leakage of electrolyte 

please contact your dealer immediately 

Power Supply 

The operating voltage range of the power adaptor should cover the 

local power supply for proper operation. The power cable, the power outlet 
and any power fusing arrangements must conform to local safety regulations. 

Please 

never do any connection / disconnection

 when system is still 

powered on. 

Please always keep the system in a free air circulation. 

POWER ON/OFF 

Power Indicator 

 

The power indicator is the backlight LED module under the logo that 

serves for several purposes. The relationship between the indicator status and 
other conditions is summarized in following table: 

Indicator Status 

System 

Status 

External 

Power 

UPS Battery  Powering Up 

Off 

Off 

Off 

Not present  Not possible 

Off 

Off 

Off 

Present 

Not allowed 

Green 

Off 

On 

No influence 

Allowed 

Blue 

On 

On 

No influence  Not required 

Blue/flash 

On 

Off 

Activated 

Not required 

Blue/rapid flash 

On 

Off 

Running at 

low capacity 

Not required 

The LED  module indicates Power/StandBy status. When it lights up 

in green, it means that the external AC power is standing by with the system 
powered off. It turns into blue when the system is powered up.  This  module 
also indicates the status of system working on battery power by flashing in 

Summary of Contents for FT-6315





















Reviews: