background image

Chapter 2: Installation 

 
A printed Quick-Start Guide (QSG) is packed with the card for your convenience.  If you’ve already performed the 
steps from the QSG, you may find this chapter to be redundant and may skip forward to begin developing your 
application.   
 
The software provided with this card is on CD and must be installed onto your hard disk prior to use. To do this, 
perform the following steps as appropriate for your operating system. 
 

Configure Card Options via Jumper Selection 

Before installing the card into your computer, carefully read Chapter 3: Option Selection of this manual, then 
configure the card according to your requirements. Our Windows based setup program can be used in conjunction 
with Chapter 3 to assist in configuring jumpers on the card, as well as provide additional descriptions for usage of 
the various card options.

 

 

CD Software Installation 

 
The following instructions assume the CD-ROM drive is drive “D”.  Please substitute the appropriate drive letter for 
your system as necessary. 

 
DOS 

1.  

Place the CD into your CD-ROM drive. 

2.  

Type 

B-

 to change the active drive to the CD-ROM drive. 

3.  

Type 

GLQR?JJ-

 to run the install program. 

4.  

Follow the on-screen prompts to install the software for this board. 

 

WINDOWS 

1.  

Place the CD into your CD-ROM drive. 

2. 

The system should automatically run the install program. If the install program does not run promptly, click 

START | RUN and type 

BGLQR?JJ

, click OK or press 

-

3.  

Follow the on-screen prompts to install the software for this board. 

 

LINUX

 

1. 

Please refer to linux.htm on the CD-ROM for information on installing under linux.  

 
 
 
 

Caution! * ESD A single static discharge can damage your card and cause premature failure! Please 

follow all reasonable precautions to prevent a static discharge such as 
grounding yourself by touching any grounded surface 

prior to touching the 

card.

 

Manual PCI-DIO-48(S) 

9

Summary of Contents for PCI-DIO-48
























Reviews: