background image

 

 

 

 

-7- 

8.1 When you login the web page, you can see the demo system current system 

information like firmware version, company… etc in this page. 

8.2 Also you can see the function lists in the left side. You can use mouse to click the 

function you want to set up. 

 

9  Mobile 

9.1 

Mobile Status 

 

(1)Operator

The SIM card of telecom carrier is been registered 

(2)SIM Card ID

SIM card ID. 

(3)Signal Quality

Signal quality.  

(4)Registration State: 

0,0  --->

Not registered, ME is currently not searching for new operator 

There is a 

technical problem. User intervention is required. Yet, emergency calls can be made 
if any network is available. Probable causes:  
• no SIM card available • no PIN entered  
• no valid Home PLMN entry found on the SIM 

0,1  --->

Registered to home network

 

0,2  --->

Not registered, but ME is currently searching for a new operator 

The ME 

searches for an available network. Failure to log in until after more than a minute 
may be due to one of the following reasons:  
• No network available or insufficient Rx level.  
• The ME has no access rights to the networks available.  
• Networks from the SIM list of allowed networks are around, but login fails due to 
one of the following reasons:  
- #11 ... PLMN not allowed  
- #12 ... Location area not allowed  
- #13 ... Roaming not allowed in this location area After this, the search will be 
resumed (if automatic network search is enabled).  

0,3  --->

Registration denied

 

0,4  --->

Unknown (not used)

 

0,5  --->

Registered, roaming 

*ME: Mobile Equipment Phonebook

 

(5)GSM S/N : IMEI Number 
(6)Motion State: The status of SIM card

Summary of Contents for MV-370S








































Reviews: