background image

 

No Diving or Jumping. 

 Observe all Safety Rules.

1-8

Remember:

Failure to install the 

“pool Winterizing Kit” 

and follow the winter-

izing procedures, in 

accordance with theses 

instructions, may void 

the pool warranty.

6. Pool Accessories

Remove all pool accessories from the pool, including the ladder. Leave the skimmer and filter

parts 

attached 

to the pool wall.  Ensure that the skimmer lid is installed 

and the opening at the

bottom of the skimmer is open so that accumulated water can drain immediately.
7. The Filter

Disconnect the filter from the pool.  Follow the filter directions for winterizing your filter.

Important Winterizing Notice

All Pools:

The water level must be maintained at least 3” (7,62cm) below the skimmer 

opening throughout the winter.  Surplus water must be removed by pumping, draining or 

siphoning so that it doesn’t enter the skimmer during the winter.  

Remove all hoses at-

tached to the skimmer and return fittings. The opening at the bottom of the skimmer 

MUST be kept open so that accumulated water can drain immediately.
Pools with 12” (30cm) skimmers:

In addition to the above, the Pool Winterizing Kit (Part Number 1370138) must be in-

serted into the 12” (30cm) skimmer (see illustration below)

Failure to install the “Pool Winterizing Kit” and follow the winterizing procedure, 

in accordance with these instructions, may void the pool warranty.

The Pool Winterizing Kit (Part Number 1370138) is also available from your pool dealer.

All Pools:

Do not attach the pool cover to the top ledge, connectors or any part of the skimmer.

Insert the Pool Winterizing Kit (Part Number 1370138) into the skimmer until it fits flush 

with the skimmer flange.  On some skimmers, it may be necessary to trim the foam to 

make a friction fit and/or use a wooden wedge to keep it in place during the winter.

Pool Wintering Kit

12” Wide Mouth Skim-

mer

Maintain water level at 

least 3” (30cm) be-

low skimmer opening 

throughout the winter

3”(7,62cm) 

Summary of Contents for PRETIUM




















Reviews: