background image

 

No Diving or Jumping. 

 Observe all Safety Rules.

1-2

A. Introduction to Installing your Pool

Read all instructions completely before you begin.

These instructions explain how to install your pool. Simply follow the step-by-step direc-

tions. Start with this part, 

S

ection

 1

 and use the other instructions, 

S

ection

 2 to 4 

to put 

together your entire pool.

S

ection

 1 

also has 

Safety Rules 

and instructions to help you keep your pool clean and 

in good shape, year after year. Be sure to read the 

Safety Rules

, and make sure everyone 

who uses your pool reads and understands them.

B. Determine a Location for your Pool

1. The Terrain

Pay special attention to choosing the right location for your pool:

• Choose a large area, as flat and level

as possible.

• Choose a spot on dry, firm earth

(stabilizer or other)—

do not 

install

the pool on asphalt, tar paper, sand,

gravel, peat moss, wood or chemi-

cally treated soil.

• Check with your pool dealer to see if

Nut Grass grows in your area. This

type of grass may grow up through

your pool liner. Your dealer will be

able to advise how best to treat the

site.

• Sloped areas will need to be made

level by digging away high spots, 

not

by filling low spots—be prepared to

hire earth-moving equipment if nec-

essary.

1

2

3

4

Important Note:

Ground preparation is 

one of the most impor-

tant steps in the installa-

tion process. A 

proper 

foundation 

will ensure 

the rest of the pool as-

sembly goes smoothly 

and that no problems 

will occur when the 

pool is filled with water.

Summary of Contents for PRETIUM




















Reviews: