Pontiac GRAND AM 2004 Owner'S Manual Download Page 274

Page: 274 / 362

2. Lift and pull the headlamp assembly forward, out of

the mounting bracket.

3. Turn the bulb assembly retainer counterclockwise

one-sixth of a turn and pull out the bulb assembly.

4. Unclip the bulb assembly from the wiring harness.

5. After replacing the bulb, reverse Steps 1 through 4

to reinstall the bulb assembly and headlamp
assembly.

Front Turn Signal and Parking
Lamps

1. Remove the headlamp assembly. Refer to the

removal procedure earlier in this section.

2. Turn the bulb assembly retainer and pull out

the bulb.

3. Unclip the bulb assembly from the wiring harness.

4. When replacing the bulb, be sure to properly

align the bulb with the locating feature in the
assembly.

5. Reverse Steps 1 through 3 to reinstall the bulb

assembly.

Center High-Mounted Stoplamp
(CHMSL)

1. Open the trunk lid and locate the center

high-mounted stoplamp on the inside of the lid.

2. Remove the three screws.

3. Gently remove and replace the bulb(s).

4. Reverse Steps 1 and 2 to reassemble the lamp

assembly.

5-48

Summary of Contents for GRAND AM 2004











































































































































































































































































































































































Search results

Summary of Contents for GRAND AM 2004

Reviews:

Brands by name

Popular brands

Pontiac GRAND AM 2004, Owner'S Manual

Search results

Summary of Contents for GRAND AM 2004

Reviews:

Brands by name

Popular brands