manualshive.com logo in svg

Pontiac GRAND AM 2004, Owner'S Manual

Share
Download
Pontiac GRAND AM 2004 Owner'S Manual Download Page 117

The cruise control will turn off if any of the following
occur:

•

The brakes are applied,

•

the clutch pedal is applied (manual transaxle),

•

the automatic transaxle is shifted to NEUTRAL (N),

•

the parking brake is applied, or

•

the brake system warning light is on.

{

CAUTION:

•

Cruise control can be dangerous where
you can not drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.

•

Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
needless wheel spinning, and you could
lose control. Do not use cruise control on
slippery roads.

Your vehicle may have Enhanced Traction System
(ETS). See Enhanced Traction System (ETS) on
page 4-9. If your vehicle is in cruise control while the
ETS begins to limit wheel spin, the cruise control
will automatically disengage. When road conditions allow
you to safely use it again, you may turn the cruise
control back on.

Setting Cruise Control

{

CAUTION:

If you leave your cruise control on when you
are not using cruise, you might hit a button
and go into cruise when you do not want to.
You could be startled and even lose control.
Keep the cruise control switch off until you
want to use cruise control.

1. Press cruise ON OFF.

2. Get up to the speed you want.

3. Press the SET COAST button and release it.

4. Take your foot off the accelerator pedal.

3-11

Summary of Contents for GRAND AM 2004











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands