16
5
INSTALLATION INSTRUCTION
Important !
Connect the other equipments first before you connecting the unit with the power source.
AM loop antenna
Attach antenna loop AM to the AM ANTENNA terminal. Put and
adjust AM loop antenna position/direction to get the best AM
reception. Keep the others electrical equipment that affected
AM reception such as neon, komputer, dll.
MIC (microphone) terminal
With attaching Microphone to MIC terminal, you can use the unit
as MIC amplifier or for karaoke.
PHONES terminal
You can listen the sound of the unit through the stereo headphones, connect stereo headphones to Phones
terminal. The both speaker will mute when you connect a headphone to the headphone terminal.
Remote Control battery installation : Open the battery cover and insert two batteries size “CR 2032” with the
right polarity.
Effective operational distance of remote control is 6 metres. If operational distance is decrease, change the
batteries with the new ones.
- Do not use different kind batteries.
- Remove the batteries if remote control does not use for along time.
- Remote control will does not work well if :
* Between remote control and the remote sensor is blocked by something.
* There is bright lights like direct sunlight.
* You operate another remote near the remote.
MW
LOOP
REAR PART OF
THE UNIT
RADIO OPERATING INSTRUCTION
Choose the signal strength based receiving position
1. If the unit position is far from the radio transmitter, activate the FM DX function.
FM DX mode is used to strengthened the radio signal although the distance is far
away from the unit position. Press and hold “SELECT” button for more than 2 seconds on the remote
control to activate the FM DX mode. FM DX is active indicates by FM DX appearance for a moment and A
icon lights up on the LCD screen.
2. If the unit position is near from the radio transmitter, activate the FM LOCAL
function. FM DX mode is used to suppressed the excessive noise and humming
caused by the unit position is near the radio transmitter. Press and hold “SELECT” button for more than 2
seconds on the remote control to activate FM LOCAL mode. FM LOCAL is active indicates by FM LOCAL
appearance for a moment and B icon lights up on the LCD screen.
Manual Tuning
1. Press “AM/FM” button on the front panel once or press “FUNCTION” on the
remote control repeatedly to select TUNER/RADIO function. The unit will be in
FM function showed by FM appearance on the LCD screen.
2. To change to AM radio mode, press “AM/FM” button on the front panel once
more or press “SELECT” button on the remote control. Radio frequency will
changed each time “
”/“
” button is pressed.
Automatic Tuning
Press “
” / “
” button more than 3 seconds until the unit start searching for the radio broadcast. The
searching will stop when the unit find a radio station. The searching will not stop if the signal of the radio station
is too weak.
Presetting the Radio station
The unit can saved 40 radio station for AM and FM band. If you are saved a radio station, a number will
represent it. Use the memori preset number to select the radio broadcast.
1. Select the AM or FM frequency band, then press “
” / “
” button to search for a radio station.
2. After caught a broadcast, press “PRG/MEM” button
on the remote control. For FM radio, LCD screen
displayed F _ _ blinking appearance. Then for AM
radio, LCD screen displayed A _ _ blinking appearance.
3. Press “0” - “9” button to insert the memory number.
4. Press “PROG/MEM” button again on the remote
control to save the memory number.
5. To delete the memory program, press and hold “ ” (stop) button for 2 seconds.
Select the Preset Radio Station
Select TUNER/RADIO function. Select the preferred frequency band (AM or FM). Press “0” - “9” numeric
buttons or press “
” / “
” button on the remote control or on the front panel.
Notes :
- Adjust AM LOOP antenna position and direction to get the best AM reception.
- Adjust FM TELESCOPIC atenna to get the best FM reception.
- FM stereo indicator will lights up on the LCD screen if the unit received Stereo FM broadcast and will lit if
the unit received Mono FM broadcast.
- If FM stereo reception contains noise, press “FM MODE” button to select MONO mode, noise are decreased
although the reception become MONO. To back to STEREO mode, press “AUDIO/FM MODE” again.
VIDEO OUT dan LINE OUT terminal
You can enjoy the picture of the unit’s DVD player through the TV. Connect VIDE OUT and LINE OUT terminal
to the AV IN terminal of the TV using RCA cable. If you connect this unit to the TV using VIDEO OUT and LINE
OUT terminal, you should select VIDEO AV as TV input.
MP3 IN terminal
If you has MP3/MP4 player, you can use the unit as amplifier by connecting MP3/MP4 player output terminal
to the MP3 IN terminal of the unit using 3.5 mm stereo jack.
TV
Video & Audio Input
Video & Audio Out
REAR PART OF THE UNIT
MP3 IN
MP3/MP4 PLAYER
LINE OUT / AUDIO OUT
/ HEADPHONES
