background image

110-827 

11  

Warranty 

The manufacturer agrees to correct for the original user of the product, either by repair (using new 
or refurbished parts), or at the manufacturer’s election, by replacement (with a new or refurbished 
product), any defects in material or workmanship which develop during the warranty period. The 
standard warranty is twenty-four (24) months after delivery of the product. In the event of 
replacement, the replacement unit will be warranted for the remainder of the original warranty 
period or ninety (90) days, whichever is longer. For purposes of this limited warranty, “refurbished” 
means a product or part that has been returned to its original specifications. In the event of a 
defect, these are your exclusive remedies. 

If the product should require service, contact the manufacturer’s/supplier’s office for instructions. 
When return of the product is necessary, a return authorization number is assigned and the product 
should be shipped, transportation charges pre-paid, in either its original packaging or packaging 
affording an equal degree of protection to the indicated service center. To insure prompt handling, 
the return authorization number must be placed on the outside of the package. A detailed 
explanation of the defect should be enclosed with the item. 

The warranty shall not apply if the defect or malfunction was caused by accident, neglect, 
unreasonable use, improper service, acts of God, modification by any party other than the 
manufacturer, or other causes not arising out of defects in material or workmanship. 

EXCLUSION OF IMPLIED WARRANTIES. THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, 
INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE WHICH EXTEND BEYOND THE DESCRIPTION AND PERIOD AS STATED IN THE 
OPERATOR’S MANUAL INCLUDED WITH EACH PRODUCT. 

LIMITATION ON DAMAGES. THE MANUFACTURER’S SOLE OBLIGATION UNDER THE WARRANTY 
IS LIMITED TO THE REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT AND THE 
MANUFACTURER SHALL NOT, IN ANY EVENT, BE LIABLE FOR ANY INCIDENTAL OR 
CONSEQUENTIAL DAMAGES OF ANY KIND RESULTING FROM USE OR POSSESSION OF THIS 
PRODUCT.  

Some states do not allow: (A) limitations on how long an implied warranty lasts; or (B) the exclusion 
or limitation of incidental or consequential damages, so the above limitations or exclusions may not 
apply to you. This warranty gives you specific legal rights and you may have other rights that vary 
from state to state. 

 

Manufactured by:

PolyScience 

6600 W. Touhy Avenue Niles, IL  60714  U.S.A. 

1-800-229-7569  

1-847-647-0611 

www.polyscience.com 

Summary of Contents for Histology Bath













Reviews: