background image

SETUP INSTRUCTIONS

1. Set up the pool by following all instructions comes with the pool. Do not

    fill water until the Filter Pump is properly installed. Locate  the Skimmer

    and Inlet openings on the pool wall.

3. Remove the Seal Ring       by unthreading it counter clockwise Keep 

    Skimmer Gasket       on its proper location. 

5. Assemble the wall fitting parts according to the following schematic and 

    the Filter Pump Inlet.

6. Final assembly  must look like the following schematic.

2. Dismount the Skimmer Top Cover   

5

   and take out the parts contained     

    inside. 

4. After placing the threaded intake of the skimmer inside its corresponding     

   pool hole, screw back the seal ring        tightly on its place.    

Make sure the key

feature is facing the 

correct location. 

No obvious gap must

be noticed in this zone.

Make sure the two rubber keyways 

are properly located after installation. 

Make sure the pool liner lies 

on this round surface, and does 

not fall into the thread slots. 

It may cause water seepage.

thread slots

Make sure the hose clamp

is located at the right over the

O-Ring        location, to ensure 

proper sealing. 

canister

Hose end align

with the step 

Inlet

opening

Skimmer opening

WARNING: 

POSITION THIS PRODUCT AWAY FROM THE POOL, SO AS TO PREVENT CHILDREN FROM CLIMBING ON IT AND ACCESSING THE POOL.

Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.

5

9

OWNER’S MANUAL

Summary of Contents for SUMMER WAVES SKIMMERPLUS SFX1000-BS



















Reviews: