manualshive.com logo in svg

Polyaire Zonemaster Unipoint RF, Owner’S Manual & Setup Manual

Share
Download
Polyaire Zonemaster Unipoint RF Owner’S Manual & Setup Manual Download Page 19

ZONEMASTER UNIPOINT RF DAMPER CONTROL SYSTEM 

- Setup Guide

Page 

6)

  Information sheet 

 

 

The following table is designed to assist installation and commissioning:

ADDRESS

NAME

Zone 

Zone 2

Zone 

Zone 

Zone 

Zone 

Zone 

Zone 8

PARAMETER

VALUE

System Code

Zone Number

High Limit

Low Limit

Spill/Bypass

Turbo

7)

  Troubleshooting guide

PROBLEM

SUGGESTED ACTION

Dampers have no  

response when 

turned on or off

•  Check if the LEDs on the main control board light up.  
  If not, check that system codes for handset and main  
  control boards are the same.

•  Check the cable to the main control board with cable tester.

Some zones cannot 

be turned off

•  Check if it is spill zone (with lower address) 

•  Check spill setpoint.

•  Check the battery level of the remote controller

No display on the 

LCD

•  Check if the battery is flat via indicator icon on screen.

•  Change to a new set of  3 x AAA battery.

 

Please contact distributors for any other problems not listed as above.

Summary of Contents for Zonemaster Unipoint RF

























Reviews:

No comments

Brands by name

Popular brands

Load more brands