Poly G7500 Administrator'S Manual Download Page 78

Page: 78 / 119

Configuring Video and Camera Settings

Topics:

▪

HDMI I/O

▪

Supported HDCI Input Resolutions

▪

Configure Monitor Settings

▪

Configure a Touch Monitor

•

Monitors with CEC

▪

Configure General Camera Settings

▪

Reset Camera Settings to Defaults

▪

Calibrate EagleEye Producer Group Framing

▪

Supported USB Cameras

▪

Selecting the Primary Camera

▪

Configuring Video Input Settings

You can configure video settings for your system, including monitors and cameras.

Use the information about supported HDMI I/O resolutions and codec capabilities to optimize your video
experience based on your deployment requirements.

HDMI I/O

Your system has HDMI input and output ports.

Your system has the following HDMI connections:

▪ Output for connecting the primary system monitor (Monitor 1)
▪ Output for connecting the secondary system monitor (Monitor 2)

The Studio X30 system doesn’t have a second HDMI output.

▪ Input for content sharing, including audio streaming

Note the following:

▪ The system supports only HDMI-to-HDMI connections and doesn’t support display conversions,

such as VGA-to-HDMI or HDMI-to-DVI cable converters.

▪ The HDMI specifications don’t provide maximum cable length definitions. The requirements defined

in the specification implicitly give rise to length limitations that are based on the cable’s construction.

▪ As with other Polycom hardware, the HDMI ports on your system meet HDMI specification

requirements. HDMI signal quality is dependent on every cable and connector in the HDMI path.

Passive HDMI extenders, female-female couplers, and wall plates are potential points of failure and

signal loss.

▪ A high-quality passive cable of minimum length provides the most repeatable solution. As the power

level of HDMI output devices can vary greatly, keep the distance from the HDMI source to the

system input as short as possible.

Summary of Contents for G7500
























































































































Search results

Summary of Contents for G7500

Reviews:

Related manuals for G7500

Brands by name

Popular brands

Poly G7500, Administrator'S Manual

Search results

Summary of Contents for G7500

Reviews:

Related manuals for G7500

Brands by name

Popular brands