manualshive.com logo in svg

Poly G7500, Administrator'S Manual, Page: 85 / 119

Share
Download
Poly G7500 Administrator'S Manual Download Page 85

▪ If you disconnect the current people camera, the system falls back to the next priority camera.

The system observes the following camera type priority:

1.

Embedded camera

2.

HDCI camera

3.

USB camera

4.

HDMI source set to display as people

Maximum Number of Supported Camera Connections

Your systems support a limited number of cameras for use in and out of calls.

This is only available when the system is in Poly Video Mode or Zoom Rooms.

Each system supports the following number of cameras:

Maximum Number of Connected Cameras

System

Cameras

G7500

Supports a maximum of two connected cameras at a
time.

▪

One USB-A camera

▪

One HDCI camera

Studio X50

Supports a maximum of one connected camera at a
time.

▪

One USB-A camera

▪

Built-in camera

Studio X30

Doesn't support multicamera connections.

Configuring Video Input Settings

You can customize your video input settings, such as enabling connected cameras, adjusting camera
orientation, or specifying whether people or content display on connected monitors.

Your system supports two video inputs. For example, a 

People

 source has pan, tilt, zoom, and near/far

camera control settings, while a 

Content

 source doesn’t.

Configure General Video Input Settings

Available settings vary depending on your video input sources.

Procedure

1.

In the system web interface, go to 

Audio/Video

 > 

Video Inputs

.

2.

Go to the input of a connected camera.

3.

Configure the following settings:

Configuring Video and Camera Settings

84

Summary of Contents for G7500
























































































































Reviews:

No comments