Polarstart PS-3085 SH Installation Manual Download Page 9

Page: 9 / 18

MODE 1

(The * indicates the default setting.)

FUNCTION 1 – Ignition-Controlled Door Locks

OPTION 1*

Ignition Locks ENABLED

OPTION 2

Ignition Locks DISABLED

OPTION 3

Ignition LOCK only

OPTION 4

Ignition UNLOCK only

FUNCTION 2 – Secure Lock

OPTION 1*

Secure Lock DISABLED (1.0 Sec Disarm pulse)

OPTION 2

Smart Secure Lock ENABLED

OPTION 3

Secure Lock DISABLED (0.5 Sec Disarm pulse)

OPTION 4

Standard Secure Lock Enabled

FUNCTION 3 – Passive / Active Starter Kill Mode

OPTION 1*

Starter Kill PASSIVE (1-minute timeout)

OPTION 2

Starter Kill ACTIVE

OPTION 3

Starter Kill PASSIVE (3-minute timeout)

OPTION 4

Starter Kill ACTIVE (G.O, IGN and ACC on 1/4 sec. before Door Locks)

FUNCTION 4 – Door locks Timing

OPTION 1*

7/10-sec. LOCK / UNLOCK pulses

OPTION 2

4-sec. LOCK / UNLOCK pulses

OPTION 3

7/10-sec. LOCK pulse, and TWO – 1/2 sec. UNLOCK pulses

OPTION 4

1/10-sec. LOCK and 1/10-sec. UNLOCK pulses

MODE 2

(The * indicates the default setting.)

FUNCTION 1 – Safe Start Mode

OPTION 1

SAFE START – ENABLED

OPTION 2*

SAFE START – DISABLED

OPTION 3

SWAP START:

START button = LOCK + UNLOCK

AUX 2 = START button

FUNCTION 2 – Engine Run Time

OPTION 1

Run time = 4 minutes in Gas Mode / 9 minutes Diesel Mode

OPTION 2*

Run time = 15 minutes in Gas Mode / 20 minutes Diesel Mode

OPTION 3

Run time = 25 minutes in Gas Mode / 30 minutes Diesel Mode

FUNCTION 3 – Turbo Mode

OPTION 1

Turbo Mode

–

ENABLED

OPTION 2*

Turbo Mode – DISABLED

FUNCTION 4 – Gas or Diesel Mode

OPTION 1

DIESEL Engine Mode (Cold Weather Mode run time = 20 min.)

OPTION 2*

GASOLINE Engine Mode

OPTION 3

DIESEL Engine Mode

MODE 3

(The * indicates the default setting.)

FUNCTION 1 – Home Valet Mode

OPTION 1

Home Valet – ENABLED

OPTION 2*

Home Valet – DISABLED

FUNCTION 2 – Zone 3 / AUX 3

OPTION 1

Constant while TRUNK button is pressed

OPTION 2*

1-sec. output while TRUNK button is pressed for 3-sec

OPTION 3

TRUNK output with DISARM / REARM pulse.

Summary of Contents for PS-3085 SH



















Search results

Summary of Contents for PS-3085 SH

Reviews:

Related manuals for PS-3085 SH

Brands by name

Popular brands

Polarstart PS-3085 SH, Installation Manual

Search results

Summary of Contents for PS-3085 SH

Reviews:

Related manuals for PS-3085 SH

Brands by name

Popular brands