Polaris Sportsman 9921344 Owner'S Manual Download Page 73

Page: 73 / 135

MAINTENANCE

Lubrication Guide

Check and lubricate all components at the intervals outlined in the Peri-
odic Maintenance Chart beginning on page 68. Items not listed in the
chart should be lubricated at the General Lubrication interval.

Item

Lube

Method

Engine Oil

PS-4 PLUS Performance

Synthetic 2W-50

See page 74.

Brake Fluid

DOT 4 Only

See page 86.

Transmission Oil

Polaris AGL Synthetic

Gearcase Lube

See page 78.

Front Demand Drive

Unit (Front Gearcase)

Premium Demand Drive

Hub Fluid

See page 81.

Front Prop Shaft Yoke

Polaris Premium U-Joint

Lube

Grease fittings (3 pumps maxi-

mum) every 500 miles (800 km),

before long periods of storage, or

after pressure washing or sub-

merging.

Control Arm (front and

rear)
Bearing Carrier
Transmission (upper

pivot point)

Front Prop Shaft Yoke

Bearing

Carrier

Control Arms

Transmission Upper

Pivot Point

Summary of Contents for Sportsman 9921344








































































































































Search results

Summary of Contents for Sportsman 9921344

Reviews:

Related manuals for Sportsman 9921344

Brands by name

Popular brands

Polaris Sportsman 9921344, Owner'S Manual

Search results

Summary of Contents for Sportsman 9921344

Reviews:

Related manuals for Sportsman 9921344

Brands by name

Popular brands