Polaris Sportsman 9921169 Owner'S Manual Download | Manualshive

Page: 72 / 137

background image

72

MAINTENANCE

Periodic Maintenance Chart

Careful periodic maintenance will help keep your vehicle in the safest,
most reliable condition. Inspection, adjustment and lubrication of
important components are explained in the periodic maintenance chart.

Inspect, clean, lubricate, adjust and replace parts as necessary. When
inspection reveals the need for replacement parts, use genuine Polaris
parts available from your Polaris dealer.

Record maintenance and service in the Maintenance Log beginning on
page 135.

NOTE:

Service and adjustments are important for proper vehicle operation. If

you're not familiar with safe service and adjustment procedures, have

a qualified dealer perform these operations.

Maintenance intervals in the following chart are based upon average
riding conditions and an average vehicle speed of approximately 10
miles per hour. Vehicles subjected to severe use must be inspected and
serviced more frequently.

Severe Use Definition

• Frequent immersion in mud, water or sand
• Racing or race-style high RPM use
• Prolonged low speed, heavy load operation
• Extended idle
• Short trip cold weather operation

Pay special attention to the oil level. A rise in oil level during cold
weather can indicate contaminants collecting in the oil sump or crank-
case. Change oil immediately if the oil level begins to rise. Monitor the
oil level, and if it continues to rise, discontinue use and determine the
cause or see your dealer.

«
...
70
71
72
73
74
...
»

Summary of Contents for Sportsman 9921169










































































































































Reviews:

No comments

Related manuals for Sportsman 9921169

Brand: KYMCO Pages: 1

Brand: Polaris Pages: 147

TRX250EX Sportrax250EX

Brand: Honda Pages: 203

Brand: Yerf-Dog Pages: 59

Brand: PRONAR Pages: 135

Brand: E-TON Pages: 38

Brand: Kayo Pages: 4

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 94

POWERSPORTS FR5DGK

Brand: MotoTec Pages: 32

Brand: Hammerhead Pages: 55

Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL

Brand: Kendon Pages: 20

Brand: Crossfire Pages: 56

Brand: Crossfire Pages: 56

Brand: Precision Pages: 9

Brand: Nitro motors Pages: 50

POLARIS RANGER 800 XP 4x4

Brand: Kolpin Pages: 68

CAN-AM Commander 1000 Limited

Brand: Kolpin Pages: 111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands