Polaris Sportsman 9921169 Owner'S Manual Download | Manualshive

Page: 27 / 137

background image

27

SAFETY

Operator Safety

WARNING

POTENTIAL HAZARD
Traveling downhill improperly.
WHAT CAN HAPPEN
Improperly descending a hill could

cause loss of control or overturn.
HOW TO AVOID THE HAZARD
Always follow proper procedures for

traveling down hills as described in

the owner's manual. NOTE: A special

technique is required when braking

while traveling downhill. See page 65.
Always descend a hill with the transmission in forward gear. Do not descend

a hill with the transmission in neutral. Always move the 4X4 switch to ADC

4X4 before ascending or descending a hill. See page 44.
Always check the terrain carefully before descending a hill.
Shift your weight rearward.
Never travel down a hill at high speed.
Avoid traveling down a hill at an angle, which would cause the vehicle to lean

sharply to one side. Travel straight down the hill when possible.

WARNING

POTENTIAL HAZARD
Improperly crossing hills and turning on hills.
WHAT CAN HAPPEN
Improperly crossing or turning on hills could

cause loss of control or overturn.
HOW TO AVOID THE HAZARD
Never attempt to turn the ATV around on any

hill until you've mastered the turning

technique (on level ground) as described in

the owner's manual. See page 66. Use extra

caution when turning on any hill.
Avoid crossing the side of a steep hill.
When crossing the side of a hill:
Always follow proper procedures as described in the owner's manual.
Avoid hills with excessively slippery or loose surfaces.
Shift your weight to the uphill side of the ATV.

«
...
25
26
27
28
29
...
»

Summary of Contents for Sportsman 9921169










































































































































Reviews:

No comments

Related manuals for Sportsman 9921169

Raider Extreme 1100D

Brand: Dazon Pages: 85

Brand: J&J Amusements Pages: 272

Brand: Yamaha Pages: 3

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 32

Brand: Yamaha Pages: 42

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 73

WOLVERINE YFM35XV

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 136

Brand: Yamaha Pages: 138

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands