background image

103

TROUBLESHOOTING

Engine Troubleshooting

Problem

Probable Cause Solution

Engine turns but fails 
to start

Faulty ignition

• Install new spark plug(s). If engine 

still fails to start, check for spark. If 
there's no spark, SEE YOUR 
DEALER.

No fuel to engine

• Make sure the fuel valve is on.
• Make sure tank contains fuel.
• Ice may be in the fuel line, filter or 

pump. Add isopropyl alcohol to the 
fuel system.

• SEE YOUR DEALER.

Poor engine com-
pression

• This indicates a major engine prob-

lem that must be repaired before 
operating. SEE YOUR DEALER.

Engine lacks power

Fouled or defective 
spark plug(s)

• Replace the plug(s).

Fuel filter (loss of 
high RPM power)

• SEE YOUR DEALER.

Plugged fuel filter or 
tank pick-up sock

• SEE YOUR DEALER.

Incorrect clutching

• SEE YOUR DEALER.

Engine continually 
backfires

Faulty plug(s)

• Change plug(s).

Fuel System

• Dirt or ice may be in the fuel system 

(deicer should be added to non-etha-
nol fuel at all times for assurance 
against fuel line icing).

Incorrect throttle 
freeplay or faulty 
switch

• SEE YOUR DEALER.

Engine requires 
more than normal 
pulls to start

Poor fuel

• Replace with fresh winter fuel.

Not enough fuel get-
ting to engine

• SEE YOUR DEALER.

Plugged fuel filter or 
tank pick-up sock

• SEE YOUR DEALER.

Summary of Contents for 800 switchback assault





























































































































Reviews: