Polaris 800 switchback assault Owner'S Manual Download Page 106

Page: 106 / 124

102

TROUBLESHOOTING

Engine Troubleshooting

Problem

Probable Cause Solution

Noise in drive
system

Broken drive clutch
components

• SEE YOUR DEALER.

Bearing failure/
chaincase, jackshaft,
or front drive shaft

• SEE YOUR DEALER.

Drive belt surface
flat spots

• Inspect and replace as needed.

Drive chain loose

• Inspect and adjust (or replace).

Drive chain worn,
sprocket teeth bro-
ken

• SEE YOUR DEALER.

Poor low RPM
performance

Worn drive belt

• Inspect and replace as needed.

Excessive belt/
sheave clearance

• SEE YOUR DEALER.

Sticky clutch

• SEE YOUR DEALER.

Poor fuel quality

• Use 87-91 octane fuel (or higher).

Engine doesn't turn

Seized engine

• SEE YOUR DEALER. Seizure is a

result of poor lubrication, inade-
quate fuel supply, broken parts or
improper cooling.

Hydrostatic lock

• Fuel may have entered the crankcase

while the vehicle was standing or
being transported. SEE YOUR
DEALER to correct the cause. Drain
plug(s) are located on the lower
crankcase for emergency draining.

Summary of Contents for 800 switchback assault





























































































































Search results

Summary of Contents for 800 switchback assault

Reviews:

Related manuals for 800 switchback assault

Brands by name

Popular brands

Polaris 800 switchback assault, Owner'S Manual

Search results

Summary of Contents for 800 switchback assault

Reviews:

Related manuals for 800 switchback assault

Brands by name

Popular brands