Polaris 600 Dragon SP Owner'S Manual Download | Manualshive

Page: 28 / 153

background image

26

SAFETY

Operator Safety

POTENTIAL HAZARD
Stalling, rolling backwards or

improperly dismounting while

climbing a hill.
WHAT CAN HAPPEN
The vehicle could overturn.
HOW TO AVOID THE

HAZARD
Maintain steady speed when

climbing a hill.
If all forward speed is lost:
Keep your weight uphill.
Apply the single lever brake gradually.
When fully stopped, apply the auxiliary rear brake as well, then

lock the parking brake.
If the ATV begins rolling backwards:
Keep weight uphill.
Never apply engine power.
Never apply the auxiliary rear brake while rolling backwards.
Apply the single-lever brake gradually.
When fully stopped, apply the auxiliary rear brake as well, and

then lock the parking brake.
Dismount on uphill side, or to either side if ATV is pointed

straight uphill.
Turn the ATV around and remount, following the procedure

described in the owner’s manual. See page 69.

WARNING

«
...
26
27
28
29
30
...
»

Summary of Contents for 600 Dragon SP


























































































































































Reviews:

No comments

Related manuals for 600 Dragon SP

Brand: SCHUBERTH Pages: 41

Brand: AFX Pages: 52

Brand: GAS GAS Pages: 131

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 12

Brand: Hama Pages: 22

Brand: Yamaha Pages: 5

1985 XV700 Virago

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 100

2007 V Star XVS650AW

Brand: Yamaha Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands