background image

Plug-In Solar 

289 London Road | Burgess Hill | West Sussex | RH15 9QU 
www.pluginsolar.co.uk | [email protected] | 01444 672005 

Page 6 

WARNINGS 

 

Never  disconnect  the  DC  wire  connectors  under  load.  Ensure  that  no  current  is 
flowing in the DC wires prior to disconnecting. An opaque covering may be used to 
cover the module prior to disconnecting the module.  
 
Do  not  touch  any  live  parts  in  the  system,  including  the  Solar  array,  when  the 
system has been connected to the electrical grid.  
 
Prior  to  installing  any  of  the  Micro-Inverters,  verify  that  the  utility  voltage  at  the 
point of common connection matches the voltage rating on Micro-Inverter label.  
 
Do  not  mount  the  Micro-Inverter  in  a  location  that  allows  exposure  to  direct 
sunlight.  Allow  a  minimum  of  3/4’’(1.5cm.)  between  the  roof  and  the  bottom  of  the 
Micro-Inverter to allow proper airflow.  
 
Always  disconnect  AC  power  before  disconnecting  the  PV  module  wires  from  the 
Micro-Inverter.  The  AC  connector  of  the  first  Micro-Inverter  in  a  branch  circuit  is 
suitable, as a disconnecting means, once the AC branch circuit breaker in the load 
center has been opened.  
 
The Micro-Inverter is powered by PV module DC power. Make sure you disconnect 
and reconnect the DC connections to watch for the three short flashes. 

 
 
 

 

Summary of Contents for Sheet Metal/Flat Roof Mount Kit






































Reviews: