manualshive.com logo in svg

Plug-In Solar Sheet Metal/Flat Roof Mount Kit, Installation Instructions Manual, Page: 37 / 37

Share
Download
Plug-In Solar Sheet Metal/Flat Roof Mount Kit Installation Instructions Manual Download Page 37

www.clenergy.com        

 

       Page 1 of 1 

 

WARRANTY - ezRack Trapezoidal 

10 Years Standard Warranty Terms and Conditions, 20 Year 
Designed Service Life 

 

Clenergy international co. Ltd warrants to the original purchaser 

(“Purchaser”) of product(s) that it manufactures (“Product”) at the original 
installation site that the Product shall be free from defects in material and 
workmanship for a period of ten (10) years, except for the anodised finish, 
which finish shall be free from visible peeling, or cracking or chalking under 

normal atmospheric conditions for a period of five (5) years, from the earlier 
of 1) the date the installation of the Product is completed, or 2) 30 days after 
the purchase of the Product by the original Purchaser (“Finish Warranty”). 

 

The Finish Warranty does not apply to any foreign residue deposited on the 

finish. All installations in corrosive atmospheric conditions are excluded. The 
Finish Warranty is VOID if the practices specified by AAMA 609 & 610-02 – 
“Cleaning and Maintenance for Architecturally Finished Aluminum” 
(www.aamanet.org) are not followed by Purchaser. This Warranty does not 
cover damage to the Product that occurs during its shipment, storage, or 

installation. 

 

This Warranty shall be VOID if installation of the Product is not performed in 
accordance with Clenergy’s written installation instructions, or if the Product 
has been modified, repaired, or reworked in a manner not previously 

authorized by Clenergy IN WRITING, or if the Product is installed in an 
environment for which it was not designed. Clenergy shall not be liable for 
consequential, contingent or incidental damages arising out of the use of the 
Product by Purchaser under any circumstances. 

 

If within the specified Warranty periods the Product shall be reasonably 
proven to be defective, then Clenergy shall repair or replace the defective 
Product, or any part thereof, in Clenergy’s sole discretion. Such repair or 
replacement shall completely satisfy and discharge all of Clenergy’s liability 
with respect to this limited Warranty. Under no circumstances shall Clenergy 

be liable for special, indirect or consequential damages arising out of or 
related to use by Purchaser of the Product. 

 

Manufacturers of related items, such as PV modules and flashings, may 
provide written warranties of their own. Clenergy’s limited Warranty covers 

only its Product, and not any related items. 

 

Summary of Contents for Sheet Metal/Flat Roof Mount Kit






































Reviews:

No comments