background image

26

CARE AND MAINTENANCE

 WARNING:

 Turn off heater and let cool before servicing. 

 

CAUTION:

 You must keep control areas, burner, and circulating air passageways of heater

  clean. Inspect these areas of heater before each use. Have heater inspected yearly by a

  qualified service person. Heater may need more frequent cleaning due to excessive lint

  from carpeting, bedding material, pet hair, etc.

 

WARNING

: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting  

  and property damage.

BURNER ORIFICE HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean 

burning flame. Keep these holes clear of dust, dirt, lint and pet hair. Clean these air inlet holes prior to 

each heating season. Blocked air holes will create soot. We recommend that you clean the unit every 

three months during operation and have heater inspected yearly by a qualified

service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. 

To clean these parts we recommend using compressed air no greater than 30 PSI. Your local

computer store, hardware store or home center may carry compressed air in a can. If using

compressed air in a can, please follow the directions on the can. If you don’t follow directions on the 

can, you could damage the pilot assembly.

BURNER FLAME PATTERN

Figure 29 shows a correct burner flame pattern. Figure 30 shows an incorrect burner flame pattern. 

The incorrect burner flame pattern shows sporadic, irregular flame tipping. The flame should not be 

dark or have an orange/reddish tinge.

Note: When using the heater the first time, the flame will be orange for approximately one hour until 

the log cures.

If burner flame pattern is incorrect, as shown in Figure 30

• turn heater off (see To Turn Off Gas to Appliance, page 23).

• see Troubleshooting, page 27.

2-6 inches

above logs

6-12 inches

above logs

Fig. 29 - Correct/Normal Flame Pattern 

with short flames 

Fig. 30 -Incorrect/Abnormal Flame  

Pattern with tall flames 

Summary of Contents for VFL2-EO18DT













Reviews: