background image

Copyright Planika Sp. z o.o.  

www.planikafires.com 

 

 

 

 

 

 

Information and warning alerts 

 

Lp. 

Control Panel 

Indicators 

SOUND 

SIGNALS 

event 

procedure 

cons

t

ant

 

inter

mi

ttent

 

 

 

 

If the fire is not visible - NO 
POWER. 

Make sure the device is properly connected to the power 
supply. 

If you see a fire - the device is 
in operation. 

Do not leave the device unattended by an adult. 

 

 

 

The device is ready for 
operation. 

You can run the device in accordance with section B.3 

 

 

 

No fuel in the tank 

Fill the fuel in accordance with B.2 paragraph 

 

 

 

Initial start-up of the device 

 

Wait for the appearance of fire, the light goes off. 

 

 

 

 
Works protected against too 
rapid restart of the hot device 
or the allowable temperature 
has been exceeded 
 

Allow the  device to cool down. After cooling the  device, 
the red indicator will turn off and the green indicator will 
start to flash. 

 

 

 

The device automatically 
turns off due to lack of fuel in 
the tank. 

Allow the device to cool down. After cooling the device, 
the red indicator will turn off 

 

 

× 

The fuel tank is full (with 
intermediate sound). 

It is not allowed to pour any more fuel! Close the Fanola 
filler bolt. The blue indicator will turn off, the green one 
will start to flash. 

 

×

 

 

There was a fuel spill or  

If refueling process is in progress it will cease 
automatically. Disconnect the automatic pump. Wait at 
least 1 hour to evaporate the remaining moisture and 
then close the fuel filler bolt. Hold the ECO button for 
about 5 seconds. If the alarm message reappears, wait a 
little bit longer until the rest of the moisture evaporates. 
If the message reappears, contact your service provider. 

the acceptable device 
operation temperature has 
been exceeded. 

If the alarm message appears during the start of the 
device, press the START / STOP button to turn off the 
sound and hold the ECO  button for about 5 seconds. 
If the message reappears, contact your service provider. 

 

× 

 

Operation error 

Press the START / STOP button to turn off the sound and 
hold the ECO button for about 5 seconds. 
If the message reappears, contact your service provider. 

10 

 

×

 

 

The device temperature 
below 10°C or critical 
operation error 

Press the START / STOP button to turn off the sound. 
Provide higher ambient temperature. Wait until the 
device obtains the indoor temperature. Hold down the 
ECO button for about 5 seconds. 
If the message reappears, contact your service provider. 

11 

READY

FUEL

HOT

 

× 

 

Filler bolt protection error. 

Shut the filler bolt. Press the START / STOP button to turn 
off the sound and hold the ECO button for about 5 
seconds. If the message reappears, contact your service 
provider. 

 

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

READY

FUEL

HOT

Summary of Contents for FLA 2 E#4











Reviews: