manualshive.com logo in svg

Planet WNL-9320, User Manual, Page: 16 / 41

Share
Download
Planet WNL-9320 User Manual Download Page 16

 

- 12 - 

Ad-Hoc

 – Select this mode if you want to connect to another wireless station in the 

Wireless LAN network without through an Access Point or Router. 

 

 

TX Power 

If you want to lower the transmit power of the card for saving the power of the system, 

you can select the lower percentages from the list. The lower power will cause the 

lower signal strength and the coverage range. 

 

 

Ad Hoc Wireless Mode 

When the card is set in Ad Hoc (Peer to Peer Mode), you can designate the wireless 

connection mode for the Ad Hoc network. 

802.11 B only

 – This card can be compatible with both 802.11g and 802.11b wireless 

stations. If there are only 802.11b wireless stations in the network, you can set the 

card to this mode. 

 

802.11 B/G mix

 – If you have a mix of 802.11b and 802.11g wireless stations in your 

network, it is recommended to setting the card to this mode. This mode is also the 

default setting. 

 

802.11 G only

 – This card can be compatible with both 802.11g and 802.11b wireless 

stations. If there are only 802.11g wireless stations in the network, you can set the 

card to this mode. 

 

 

Preamble 

The preamble defines the length of the CRC block for communication among wireless 

devices. This option is only active in the Ad Hoc network. 

 

There are two modes including Auto and Long Preamble. If “Auto“mode is selected, 

the card will auto switch the preamble mode depending on the wireless devices the 

card is connecting to. 

 

 

RTS Threshold 

Minimum packet size required for an RTS (Request To Send). For packets smaller 

than this threshold, an RTS is not sent and the packet is transmitted directly to the 

wireless network. Select a setting within a range of 0 to 2347 bytes. Minor change is 

recommended. 

 

 

Fragment Threshold 

The value defines the maximum size of packets; any packet size larger than the value 

will be fragmented. If you have decreased this value and experience high packet error 

rates, you can increase it again, but it will likely decrease overall network 

performance. Select a setting within a range of 256 to 2346 bytes. Minor change is 

recommended. 

 

 

Channel 

This setting is only available for Ad Hoc mode. Select the number of the radio channel 

used for the networking. The channel setting should be the same with the network you 

are connecting to. 

 

 

Summary of Contents for WNL-9320










































Reviews:

No comments