background image

Chapter 4 Specifications 

Battery: 4 * 12V 2.2Ah Valve Regulated Lead-Acid Batteries. 

Charging Instruction 

Type 

Voltage Regulation 

Initial Current 

Stand-by Use 

13.5 – 13.8V 

No Limit 

Cycle Use 

14.4 - 15.0V 

0.66A max 

Maximum charging current: 0.58A   

Charging voltage: 14.4 to 15.0V   

Float charging voltage: 13.50 to 13.80V   

Volts: 12   

Nominal Capacity (20 Hr Rate - Ah): 2.25   

Length: 178.0mm (7.01")   

Width: 34.0mm (1.34")   

Overall Height Incl. Terminals: 64.0mm (2.52")   

Weight: 0.94 kgs. (2.07 lbs.)   

Energy Density (20 Hr. Rate): 1.24 WH/cubic inch   

Specific Energy (20 Hr. Rate): 13.5 WH/lbs.   

Internal Resistance of Charged Battery: 60 milliohms (approx.)   

Maximum Discharge Current with Standard Terminals (amperes): 40   

Maximum Short-Duration Discharge Current (amperes): 75   

Charge Retention (Shelf Life) At 68 Degrees F (20 Degrees C) 1 Month: 97%   

Charge Retention (Shelf Life) At 68 Degrees F (20 Degrees C) 3 Months: 91%   

Charge Retention (Shelf Life) At 68 Degrees F (20 Degrees C) 6 Months: 85%   

Life Expectancy/Standby Use: 3-5 years   

Life Expectancy/Cycle Use (Approx.) 100% Depth of Discharge: 250 cycles   

Life Expectancy/Cycle Use (Approx.) 50% Depth of Discharge: 550 cycles   

Life Expectancy/Cycle Use (Approx.) 30% Depth of Discharge: 1200 cycles   

Sealed Construction: Can be operated, charged or stored in any position without 

leakage  

Standard Terminal: Quick Disconnect .187   

Housing Material: ABS Resin 

 

 

11

Part No.

 

2011-A92340-000

 

Summary of Contents for UPS-400













Reviews: