Planet Enterprise WiFi System User Manual Download Page 19

Page: 19 / 69

Step1: Operation Mode

This page followed by Setup Wizard page to define the operation modes.

There are 2

modes allow you configure –

Gateway

Bridge

and

WISP

mode. The default value is

“

Bridge

” mode.

Basically, the WAP-6200 is with three physical interfaces, Wireless interface, LAN

interface, and WAN interface. However, with the three operation modes above, the

logical interface could have some changes for the modes selected.

Operation

Modes

Physical

Interface

Logical Interface

Remark

LAN LAN

WAN

WAN (NAT Router)

Gateway

Wireless LAN

Bridged

LAN

LAN LAN

WAN LAN

Bridged

LAN

Bridge

Wireless LAN

Bridged

LAN

LAN LAN

WAN LAN

Bridged

LAN

Wireless

ISP

Wireless

WAN (NAT Router)

Summary of Contents for Enterprise WiFi System






































































Search results

Summary of Contents for Enterprise WiFi System

Reviews:

Related manuals for Enterprise WiFi System

Brands by name

Popular brands

Planet Enterprise WiFi System, User Manual

Search results

Summary of Contents for Enterprise WiFi System

Reviews:

Related manuals for Enterprise WiFi System

Brands by name

Popular brands