Planet Enterprise WiFi System User Manual Download Page 23

Page: 23 / 69

Chapter 6 Operation Mode

There are 2 modes allow you configure –

Gateway, Bridge

and

WISP

mode.

The default value is

“Bridge”

mode

Parameter

Description

Gateway

In this mode, the device is supposed to connect to internet
via ADSL/Cable Modem. WAN type:PPPoE, DHCP client,
PPTP client or Static IP.

Bridge

Each interface (LAN, WAN and Wireless) regards as
bridge. NAT, Firewall and all router’s functions are not
supported

Wireless ISP

Switch Wireless interface to WAN port and all Ethernet
ports in bridge mode. Wireless interface can do all router’s
functions

Apply Changes

Click the

Apply Changes

button to complete the new

configuration setting.

Reset Click

the

Reset

button to abort change and recover the

previous configuration setting.

Summary of Contents for Enterprise WiFi System






































































Search results

Summary of Contents for Enterprise WiFi System

Reviews:

Related manuals for Enterprise WiFi System

Brands by name

Popular brands

Planet Enterprise WiFi System, User Manual

Search results

Summary of Contents for Enterprise WiFi System

Reviews:

Related manuals for Enterprise WiFi System

Brands by name

Popular brands