Planet 802.11n Wireless PCI Adapter WNL-9330 User Manual Download Page 13 | Manualshive

Page: 13 / 61

background image

6. There are two wireless performance mode you can select here:

Optimize for WiFi mode

or

Optimize for performance mode

If you want to enhance wireless performance, please select ‘Optimize for performance

mode’. However, wireless compatibility is not guaranteed in this mode. If you want to use

this mode, you may not be able to communicate with older wireless devices and wireless

access point, such as 802.11b devices, but the data transfer rate will be enhanced in this

mode. You can select this mode when you only plan to communicate with 802.11 Draft-N

devices.

If you want to keep compatibility and communicate with older wireless devices, please

select ‘Optimize for WiFi Mode’.

After you finish the selection, please click ‘Next’ to continue.

If you see ‘Found New

Hardware’ message again, please ignore it and wait.

«
...
11
12
13
14
15
...
»

Summary of Contents for 802.11n Wireless PCI Adapter WNL-9330






























































Reviews:

No comments

Related manuals for 802.11n Wireless PCI Adapter WNL-9330

CHROME 400 Series

Brand: S3 Graphics Pages: 67

Brand: Hawking Pages: 2

Brand: Magtek Pages: 28

Brand: Lanpro Pages: 5

Brand: Cidron Pages: 27

Brand: ACS Pages: 13

Brand: SAMSys Pages: 36

Brand: AMX Pages: 2

Brand: Lindy Pages: 2

Parallel-PCIe/LP

Brand: Lava Pages: 1

Brand: Planet Pages: 2

Brand: Planet Pages: 25

Brand: Konig Pages: 48

Brand: ESI Pages: 30

Brand: GE Interlogix Pages: 34

Brand: GE Interlogix Pages: 36

Brand: Lindy Pages: 3

Brand: Intersil Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands