Planet Networking & Communication WDAP-C7200E User Manual Download Page 31

Page: 31 / 85

User Manual of WDAP-C7200E

-24-

DHCP

Choose “

DHCP

” and the router will automatically obtain IP addresses, subnet masks and gateway addresses

from your ISP.

Figure 5-6

Gateway – DHCP

5.2.2 Wireless

Figure 5-7

Gateway – Wireless

The page includes the following fields:

Object

Description

WLAN Status

Select

OFF

to enable or disable wireless LAN.

Wireless Analyzer

Press the button to check your wireless environment.

SSID

It is the wireless network name. The default SSID is

PLANET_2.4G

PLANET_5G

Channel

Select the operating channel you would like to use. The channel

range will be changed by selecting a different domain.

Encryption

Select the wireless encryption. The default is

None

Summary of Contents for WDAP-C7200E






















































































Search results

Summary of Contents for WDAP-C7200E

Reviews:

Related manuals for WDAP-C7200E

Brands by name

Popular brands

Planet Networking & Communication WDAP-C7200E, User Manual

Search results

Summary of Contents for WDAP-C7200E

Reviews:

Related manuals for WDAP-C7200E

Brands by name

Popular brands