Planet Networking & Communication VC-200M User Manual Download Page 49

Page: 49 / 56

The screen contains the following details:

Setting Description

Direction

Select the target direction of downstream or upstream.

Target SNRM

Set the required SNR Margin×10(50=5dB), by default is

6dB

Click “

CANCEL

” to exit from this page without saving the changes.

Click “

APPLY

” at any time during configure to save the information that you

have been entered.

4.1.3

Profile Configuration

VDSL2 was developed and standardized in record time to address the shortcomings of

existing access technologies. It servers as the ideal xDSL technology for eliminating

last-mile bottlenecks and enable global mass deployment of advance Triple Play

services.

Unlike its predecessor, which allowed choosing either DMT (Discrete Multitone) or

QAM (Quadrature Amplitude Modulation) technology, VDSL2 only uses the DMT

line code.

DMT is a method of separating a DSL signal so that the usable frequency range is

separated into multiple small frequency bands, or tone. It uses up to 4096 tones which

are spaced 4 kHz or 8 kHz apart. Each tone can be used for either downstream or

upstream.

However VC-200M/VC-200S provide 10 VDSL2 profiles: 8a, 8b, 12a, 12b, and 17a

frequency bands.

Summary of Contents for VC-200M

























































Search results

Summary of Contents for VC-200M

Reviews:

Related manuals for VC-200M

Brands by name

Popular brands

Planet Networking & Communication VC-200M, User Manual

Search results

Summary of Contents for VC-200M

Reviews:

Related manuals for VC-200M

Brands by name

Popular brands