manualshive.com logo in svg

Planet Networking & Communication ICS-2100T, User Manual, Page: 37 / 76

Share
Download
Planet Networking & Communication ICS-2100T User Manual Download Page 37

User’s Manual of ICS-2x00T  Serial Device Server  Series 

 

 

37 

 

IPv4 Configuration 

Object 

Description 

•

 

IP Configuration

 

The status of IPv4 configuration. 

•

 

IP Address 

The current IPv4 address of the device. 

•

 

Subnet Mask 

The current IPv4 subnet mask of the device. 

•

 

Gateway 

The current IPv4 gateway of the device. 

•

 

Primary DNS 

The current first DNS server of the device. 

•

 

Second DNS 

The current second DNS server of the device. 

•

 

MAC Address 

Specifies the device MAC address. 

 

IPv6 Configuration 

Object 

Description 

•

 

IP Configuration

 

The status of IPv6 configuration. 

•

 

IP Address 

The current IPv6 address of the device. 

•

 

Prefix 

The IPv6 network mask, in number of bits (prefix length). 

•

 

Gateway 

The current gateway for the IPv6 interface. 

•

 

Primary DNS 

The current first DNS server of the device. 

•

 

Second DNS 

The current second DNS server of the device. 

 

 

 

 

Summary of Contents for ICS-2100T













































































Reviews:

No comments