background image

 

  Important Safety Instructions 

 
 

Please read the following instructions carefully. This manual should be retained for future use.   

1.

 

To clean the LCD Monitor screen:   
-- Power off the LCD Monitor and unplug the AC Cord.   

 

-- Spray a non-solvent cleaning solution onto a rag.   
-- Gently clean the screen with dampened rag.   

2.

 

Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can 
severely damage it.   

3.

 

Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to the display.   

4.

 

Do not remove the cover or attempt to service this unit by yourself. Servicing of any nature should be 
performed by an authorized technician.   

5.

 

Store the LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F). Storing the LCD 
Monitor outside this range could result in permanent damage.   

6.

 

If any of the following occurs, immediately unplug your monitor and call an authorized technician.   
*    Monitor to PC signal cable is frayed or damaged.   
*    Liquid spilled into LCD Monitor or the monitor has been exposed to rain.   
*    LCD Monitor or the case is damaged.   

7.

 

Only use the supplied main lead to connect the monitor. For a nominal current up to 6A and a device weight 
above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm

2

 must be used. 

 

Important Recycle Instruction: 

 Lamp(s) inside this product contain mercury. This product may contain other 

electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in 
accordance with local, state, or federal Laws. For more information, contact the Electronic 
Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check 
WWW.LAMPRECYCLE.ORG. 

 

Contains Mercury, Dispose of Properly 

 

 

Summary of Contents for PX2611






















Reviews: