3
VOLTS
14
16
17
12
10
8
7
CYBER GAUGE
V
60
40
20
120
100
80
CYBER GAUGE
WATER
TEMP
°C
x100kPa
2.0
1.0
0
-1.0
CYBER GAUGE
BOOST
x1000rpm
0
1
2
3
4
5
6
7
8
9
CYBER GAUGE
Installing The Product
Notes about using the OBD2 Connector
How to use the Cut Connectors
1
10
mm
2
10
mm
3
4
5
When crimping, please
u s e c r i m p e r s o r u s e
pliers to bend and then
solder together.
Peel off of the vinyl
cover at connection.
Peel off of the vinyl
cover at the end of
the product’ s wire.
W r a p a r o u n d
both wire coils.
C l o s e t i g ht l y w i t h
cut connector.
Insulate with vinyl
tape.
If you unable to get a grip
on the distended portions.
M a k e s u r e t o g r i p t h e
distended portions when
pulling it out or inserting it.
D o n o t p u l l o n t h e w i r e s
when trying to remove the
connector; the wires may
become disconnected.
CAUTION
W i t h s o m e c a r m o d e l s i t
m ay b e d i f f i c u l t t o g e t a
good grip on the connector.
In such case, pull
out the connector
by p u l l i n g o n t h e
end of the zip tie.
③
Affix the Cushion Tape on the base of the meter,
connect the Gauge Cable to the Meter, and install
the Meter into the Meter Holder.
Please add the
Cushion Tape if the Meter not fixed.
①
F a s t e n u s i n g t h e
double-sided tape.
Note : Please be sure about
where you wish to install the
meter, as it is not advisable to
reuse double-sided tape.
Meter Holder
Gauge
Cable
Gauge
Cable
Back side
of Meter
Clean
to remove
oil and dust
Double-sided
tape
Installing The Meter
②
After deciding the
p o s i t i o n a n d
angle of the meter
fa c e, fa s te n t h e
Hexagonal bolt on
b o t h s i d e s t o
secure.
●
W h e n u s i n g L i n k C a b l e , p u t t h e
connector to the back of Meter Holder
as shown in the below diagram. Push
the remained cable between the meters
to inside of Meter Holder.
Cut the Cushion Tape in half, affix to base of the Meter to be
on press fit condition with adjusting number. And connect the
Gauge Cable to the Meter and insert into the panel.
Meter
Holder
Connector
Meter
Connector
Connector
Cable
Cushion Tape
Cushion
Tape
Cushion Tape
Double-sided
tape
Cushion Tape
Cushion Tape
Unit
Zip tie
(Large)
Through
holes
Thick cable
or pipe
Clean to
remove
oil and dust.
Fastening to
Flat Space
When Fastening
to a Cable or Pipe
(Example of Installation)
Installing The Unit
As shown in the above diagram , fasten
t h e u n i t i n t o p o s i t i o n s n o t u s u a l l y
affected by water.
A Must-Have
for Turbo Cars
From checking boost to estimating gas
usage (vacuum side) make this a vital
item for your turbo engine car.
For Preventing
Overheating and
Checking Warm-up
This gauge allows you to not only check
warm -up operation but help prevent
overheating due to lack of coolant or
trouble in the coolant line.
Battery Checking
for New-Era Systems
Use to calculate battery life by checking
voltage drop during idling and minimum
voltage at start up, as well as, check on
your bat ter y re c harg ing st atus from
regenerative braking.
From Sports
to Eco Driving
A b a s i c t a c h o m e t e r d e s i g n e d f o r
checking shifting performance in both
AT a n d M T c a r s , a s w e l l a s , h e l p
optimize your eco-driving.
BOOST
WATER
TEMP
VOLTAGE
TACHOMETER
Features of the meter
For some models, please connect the power cable to IGN as shown on the right.
After stopping the engine, it
takes about a minute until
the meter turns off.
Sometimes the meter is not
working.
It's a communication matter with
the car side
It's a communication matter with
the car side, but it has no trouble to
the car without changing the wiring.
Unplug the connector of Yellow and Red cable of OBD Cable
and connect Yellow cable of IGN Cable into the connector on
yellow cable, then connect to IGN cable to IGN of car. (Do not
connect to Acc)
IGN Cable
＝
Cut Connector
IGN
(12V with Key ON)
OBD Cable
Diagnostic
Monitoring
Connector
Yellow
Yellow
Red
Part of SUBARU
(Including 86)
Symptom
Cause
Part of SUZUKI
Hexagonal bolt
If connect the power cable to IGN (Not normally required)
A Installation with the Meter Holder
B Installation to panel or something
Panel
Cut the
Cushion Tape
in half
