Pitney Bowes DI380 OfficeRight Operator'S Manual Download Page 68

Page: 68 / 100

4 • Reference

4-10

SV61656 Rev. A

Message

Action

CALL SERVICE

Power machine off and on. If message still

displays, call for service.

CHECK /CLEAR

FEEDER

The feeder indicated has failed to feed materi

al. Remove material from the feed tray, reload

and restart machine.

CHECK FEEDER

The feeder indicated is not located correctly.

Remove tray and relocate. Also check loading

of material in indicated feeder.

CHECK FOLD

PLATE

Fold plate indicated is not located correctly.

Remove fold plate and relocate.

CHECK

INVERTER

Envelope inverter unit has not set to its cor

rect position. Open inverter cover and check

for any material. Close cover and restart.

CHECK LAST

MAIL PIECE

Envelope has failed to open. Check that en

velopes are loaded correctly. Reload enve

lopes and restart machine.

CLEAR FOLD

PLATE

Material was detected inside the fold plate in

dicated on the display. Remove fold plate and

check for any material. Install fold plate.

CLEAR

INSERTION AREA

Material was detected in the inserting area.

Open tinted plastic cover on left hand side

of machine and remove any material. Close

cover and restart.

CLEAR

MOISTENER

Material was detected in the sealer brush

area. Open tinted plastic cover on left hand

side of machine and remove any material.

Close cover and restart.

CLEAR SEALER

Material was detected in the sealer brush

area. Open tinted plastic cover on left hand

side of machine and remove any material.

Close cover and restart.

CLOSE COVER

Cover indicated is not fully closed. Close indi

cated cover and restart.

Error Messages

Summary of Contents for DI380 OfficeRight





































































































Search results

Summary of Contents for DI380 OfficeRight

Reviews:

Related manuals for DI380 OfficeRight

Brands by name

Popular brands

Pitney Bowes DI380 OfficeRight, Operator'S Manual

Search results

Summary of Contents for DI380 OfficeRight

Reviews:

Related manuals for DI380 OfficeRight

Brands by name

Popular brands